Whirlpool Packaged Terminal Air Conditioner Manuale delle Istruzioni

PACKAGED TERMINAL AIR CONDITIONER (PTAC) / PACKAGED TERMINAL HEAT PUMP (PTHP) AND ACCESSORY INSTALLATION INSTRUCTIONS®Table of ContentsPTAC/PTHP AND A

10WALL SLEEVE EXTENSION INSTALLATION INSTRUCTIONS Location Requirements The PTAC/PTHP is intended for mounting through an exterior wall. If the wall

115. From the inside of the building, position the wall sleeve in the opening and push it through the wall so it protrudes at least ¹⁄₄ in. (6.4 mm) o

12STANDARD GRILLE INSTALLATION INSTRUCTIONSNOTE: Unpack and dispose of packaging materials. 1. Remove the center support and weatherboard, if still in

13ARCHITECTURAL LOUVER INSTALLATION INSTRUCTIONSNOTE: Unpack and dispose of packaging materials. 1. Remove the center support and weatherboard, if sti

14WALL SLEEVE ADAPTER KIT INSTALLATION INSTRUCTIONS Unpack and dispose of packaging materials. This kit retrofits the 11¹⁄₂ in. (29.2 cm) deep wall

15Install Chassis1. Disconnect power.2. Center the chassis in the installed sleeve and carefully push the chassis until the chassis flange and gasket

16Direct Wired Models Field wiring connections for direct-wired models can be done in one of 2 ways: Using field-supplied conduit and wires Using

17CONDUIT KIT/JUNCTION BOX INSTALLATION INSTRUCTIONSTools and PartsTools needed Flat-blade screwdriverParts suppliedLocation Requirements Unpack and

182. Skip this step if incoming power supply is in subbase. Determine the location of the power supply. Position the junction box in such a way that t

198. Leave the right-angle connector off of the flexible conduit. Feed the long wires of the provided harness through the right-angle connector in the

2PTAC/PTHP AND ACCESSORY SAFETY PLANNING THE INSTALLATIONTypical Unit ComponentsNOTE: The wall sleeve and outdoor grille are not provided.You can be

20FRONT COVER SIDE MOUNT KIT INSTALLATION INSTRUCTIONSNOTE: Unpack and dispose of packaging materials. Kit Installation1. Remove front cover.2. Locate

217. Install the front cover by placing the top of the front cover onto the metal flange at the top of the chassis. Rotate the front cover into place.

22LIMITING TEMPERATURE RANGE The adjustment limiting screws under the temperature control knob can be relocated to change the maximum heat and cool s

23FAN CYCLE SWITCHOn standard models with unit-mounted controls, the fan cycle switch is located behind the front cover. It is designed to operate the

24AIR DISCHARGE GRILLE The indoor air discharge grille can be positioned to direct the air either straight up or at an angle into the room. Changing t

25Installing New Thermostat1. Disconnect power to avoid product damage during installation of new thermostat.2. Remove the PTAC/PTHP front cover.3. Lo

2614. Reconnect power.NOTE: On power up, the LCD readout will display oP momentarily, then the room temperature. Check Fan OperationFan Operation1. To

27DISCONNECT SWITCH INSTALLATION INSTRUCTIONSParts Required 12 AWG green wireLocation Requirements Unpack and dispose of packaging materials. The

287. Reattach disconnect switch cover assembly to subbase.8. Attach a 12 A.W.G. ground wire to the ground terminal on the disconnect switch and to the

29Subbase Kit Installation IMPORTANT: The installation of field wiring must conform to the requirements of the National Electrical Code, ANSI/NFPA

3Required Parts, Accessories and OptionsPart Number Description4396585 Wall sleeve - G-90 zinc coated steel is prepared in an 11-step process, then el

30IMPORTANT: The next steps require you to make permanent modifications to the decorative side skirts. The modifications are for left and right sides,

318. Reattach the PTAC/PTHP front cover using the thumbscrews removed earlier.9. Replace all subbase covers.10. Reconnect power.230/208 volt installat

3211. Pivot the control box down, pull the chassis pigtail wires into the control box, and remove the bushing from the hole. The field-supplied wires

3310. Pivot the control box down, pull the chassis pigtail wires into the control box, and remove the bushing from the hole. The field-supplied wires

348. Connect the incoming green or bare ground wire and green wire in the conduit accessory to the subbase ground lug.9. Reattach the PTAC/PTHP front

35Make Electrical Connections 230/208 Volt Power Supply Each desk control relay requires approximately 10 VA of power. Terminal numbers are marked

367. Run the harness wire ends with the quick connectors through the hole and connect them to the coil terminals of the desk control relay coil. 8. S

37Remote Thermostat Control (on some models) (remote wall thermostat installed)1. Disconnect power.2. Remove the fused, black wire from the 277 volt t

38Install Lateral Duct Adapter1. Disconnect power.2. Remove front cover.3. Remove the chassis from the wall sleeve (if installed).4. Locate and mark 4

3913. Attach the left and right mounting brackets using 4 unpainted screws.14. Remove the duct adapter discharge grille. Discard plastic wrapping.15.

4INSTALLATION REQUIREMENTSThese instructions are intended as a general guide only and do not supersede any national or local codes in any way. Complia

40PTAC/PTHP CAREYour new PTAC/PTHP is designed to give you dependable service. This section tells you how to clean and care for your PTAC/PTHP properl

41Performing MaintenanceYour PTAC/PTHP needs maintenance to help ensure steady, top performance throughout the year. 1. Disconnect power.2. Remove fro

42TROUBLESHOOTINGIf the PTAC/PTHP is not working satisfactorily, follow these basic troubleshooting suggestions.Being familiar with the sequence of op

43ASSISTANCE OR SERVICEBefore calling for assistance or service, please check “Troubleshooting.” It may save you the cost of a service call. If you st

WHIRLPOOL® PACKAGED TERMINAL AIR CONDITIONER (PTAC) AND PACKAGED TERMINAL HEAT PUMP (PTHP) WARRANTYONE YEAR FULL WARRANTYFor one year from the date of

5Location Requirements This PTAC/PTHP is intended to be installed through an exterior wall of the building where the wall is 6 in. (15.2 cm) to 13 in

6265 Volt PTAC/PTHPAll 265 volt PTAC/PTHPs are equipped with pigtail leads for field wiring.IMPORTANT: Use copper conductors only. Wire sizes are

7Internal Drain Installation(Located inside the wall cavity or in the interior of the room)NOTE: If installing an internal drain, install drain kit on

8WALL SLEEVE INSTALLATION INSTRUCTIONSWall Sleeve RequirementsIMPORTANT: The wall sleeve is designed for walls that are 13 in. (33 cm) in depth or les

9Wall Sleeve Installation1. From the inside of the building, position the wall sleeve in the opening and push it through the wall so it protrudes at l