Whirlpool OSX 896 D P 0 X Istruzioni per l'uso Scaricare il pdf (Pagina 16)

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

3. Grip the door on the two outer sides and

close it approximately half way. Pull the

door towards you, lifting it out of its slot (see

diagram). To replace the door, reverse this

sequence.

Inspecting the seals

Check the door seals around the oven regularly. If the seals are damaged,

please contact your nearest Service Centre (see Assistance). We recommend

that the oven is not used until the seals have been replaced.

Replacing the light bulb

To replace the oven light bulb:

1. Remove the glass cover of the

lamp-holder.

2. Remove the light bulb and replace

it with a similar one: halogen lamp

voltage 230 V, wattage 25 W, cap G 9.

3. Replace the glass cover (see

diagram).

! Do not touch the light bulb directly with your hands.

! Do not use the oven lamp as/for ambient lighting.

Glass cover

Lamp

Holder

compartment

Automatic cleaning with the FAST CLEAN function

With the FAST CLEAN mode, the internal temperature of the oven reaches

500°C. The pyrolytic cycle is activated, burning away food and grime

residues. Dirt is literally incinerated.

Keep children away from the appliance during the automatic cleaning cycle

as surfaces may become very hot. Particles may ignite inside the oven as a

result of the combustion process. There is no cause for concern: this process

is both normal and hazard-free.

Before initiating the FAST CLEAN mode:

• cleantheovendoor;

• removelargeorcoarsefoodresiduesfromtheinsideoftheovenusinga

dampsponge.Donotusedetergents;

• removeallaccessoriesandtheslidingrackkit(wherepresent);

• donotplaceteatowelsorpotholdersovertheovenhandle.

! If the oven is too hot, the pyrolytic cycle may not start. Wait for the oven to

cool down.

! The programme may only be started once the oven door has been closed.

!ThedesiredFastCleanmodewillbeconrmedandstartedautomatically

if the CLOCK icon button is not pressed within 10 seconds from selecting

the cooking time.

To activate the Fast Clean programme:

1. Switch the control panel on by pressing the icon.

2. Press icon ;thedisplaywillshowthetext“Piro”,“nor”andthedefault

duration of 1:30 h (normal cycle) alternately.

3. Press icon ,thenturntheTIMERknobtoadjustthedefaultcleaning

level. There are 3 different levels to choose from, each with a pre-set duration

whichcannotbemodied:

1. Economy (ECO): turn the knob towards “ ”. Duration 1 hour.

2. Normal (NOR): initial level. Duration 1 hour and 30 minutes.

3. Intensive (INT): turn the knob towards “ ”. Duration 2 hours.

4. Press the icontoconrm.

5. Press the icon to begin the cleaning cycle.

An end time for the FAST CLEAN cycle (as for a normal cooking cycle) may

be programmed (see Programming the automatic cleaning end time).

Safety devices

• thedoorlocksautomaticallyassoonasthetemperaturereachesahigh

value;the iconlightsuponthedisplay;

• pressingthe iconcancelsthecleaningcycleatanytime;

• ifamalfunctionoccurs,theheatingelementswillbeswitchedoff;

• oncetheovendoorhasbeenlocked,youcannotchangethedurationand

end time settings.

Programming the automatic cleaning end time

1. Press the icon twice: the icon and the numerical digits on the

displaywillbegintoash.

2. Turn the TIMER knob towards “ ” and “ ” to adjustthe cleaningend

time value.

3. Once you have reached the desired end time, press the icon again.

1 2 ... 11 12 13 14 15 16 17 18 19 20

Commenti su questo manuale

Nessun commento

Whirlpool OSX 896 D P 0 X Istruzioni per l'uso Pagina 16

Commenti su questo manuale

Prodotti e manuali riguardandi Piani cottura Whirlpool OSX 896 D P 0 X