Whirlpool OSD89EDE Istruzioni per l'uso Scaricare il pdf (Pagina 16)

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

2. Use a screwdriver to lift up and turn the small levers F located on the two

hinges (see diagram).

3. Grip the door on the two outer sides and

close it approximately half way. Pull the

door towards you, lifting it out of its slot (see

diagram). To replace the door, reverse this

sequence.

Inspecting the seals

Check the door seals around the oven regularly. If the seals are damaged,

please contact your nearest Service Centre (see Assistance). We recommend

that the oven is not used until the seals have been replaced.

WHEN USING THE MAIN OVEN

YOU MUST ENSURE THAT THE

BASE OF THE CAVITY IS NOT

COVERED WITH ALUMINUM

FOIL, UTENSIL OR ANY OTHER

FORM OF COVERING. FAILURE

TO DO THIS MAY RESULT IN

THE CAVITY BEING DAMAGED.

! ATTENTION

Replacing the light bulb

To replace the oven light bulb:

1. Remove the glass cover of the

lamp-holder.

2. Remove the light bulb and replace

it with a similar one: halogen lamp

voltage 230 V, wattage 25 W, cap G 9.

3. Replace the glass cover (see

diagram).

! Do not touch the light bulb directly with your hands.

! Do not use the oven lamp as/for ambient lighting.

Automatic cleaning using the Diamond Clean cycle

The Diamond Clean mode is an automatic cleaning cycle which releases

steam inside the cavity and uses the exclusive Diamond Clean enamel to

make it easy to remove any dirt residues from the cavity and accessories.

Glass cover

Lamp

Holder

compartment

Available in three different levels: Economy, Normal and Intensive - to be

used based on the type of dirt.

The Diamond Clean cycle can be used to keep the oven always clean.

During the cleaning process steam is released inside the cavity which, together

with the titanium-based Diamond Clean enamel (on the inside walls of the

oven and dripping pans), makes it easy to clean the oven.

Three different cleaning levels may be selected: Economy, Normal and

Intensive - based on the type of dirt. The following are the features of the

three different cycles.

In order to start the Diamond Clean cycle:

1. Wait for the oven to cool down.

2. Place the dripping pan on level 1 and pour in the following quantities of

water: 150g for the Economy cycle, 250g for the Normal cycle and 350g for

the Intensive cycle. A smaller or larger quantity of water than recommended

may affect the cycle results. Do not use detergents.

3. Close the oven door.

4. Press the icon

to switch on the control panel.

5. Press the icon

to display the text “dc”, “nor” and the default duration

of 15 minutes (normal cycle) alternately.

6. Press the icon

and turn the TIMER knob to adjust the default cleaning

level. There are 3 different levels to choose from, each with a pre-set duration

which cannot be changed:

1. Economy (ECO): turn the knob towards “ ”. Duration 10 minutes.

2. Normal (NOR): initial level. Duration 15 minutes.

3. Intensive (INT): turn the knob towards “ ”. Duration 20 minutes.

4. Press the icon

to conrm.

5. Press the icon

to start the cleaning process.

! To prevent any steam leaks do not open the door during the cycle.

! In the last minutes of the intensive cycle the control panel will partially and

momentarily mist up. The mist will disappear every time the tangential cooling

fan is started.

An end time for the Diamond Clean cycle may be programmed just like for a

normal cooking cycle (see Programming the automatic cleaning end time.)

Safety devices

• Press the

button to cancel the cleaning cycle at any time;

• If an anomaly occurs, the heating elements will be switched off.

Programming the automatic cleaning end time

1. Press the icon

twice. The icon and numerical digits begin to

ash on the display panel;

2. Turn the TIMER knob towards “ ” and “ ” to adjust the cleaning end

time value.

3. Once you have reached the desired end time, press again the icon

The display panel will show the duration, the cleaning end time and the set

cleaning level alternately.

4. Press the icon

to start programming.

Programming has been completed when the icons

and light up.

5. Once the cleaning process is over, “END” appears on the display panel

and a buzzer sounds.

• E.g. It is 9:00 a.m. and the Economy Diamond Clean level has been

selected, with the default duration of 10 minutes. 12:30 p.m. is scheduled

as the end time. The programme will start automatically at 12:20 p.m.

1 2 ... 11 12 13 14 15 16 17 18 19 20

Commenti su questo manuale

Nessun commento

Whirlpool OSD89EDE Istruzioni per l'uso Pagina 16

Commenti su questo manuale

Prodotti e manuali riguardandi Piani cottura Whirlpool OSD89EDE