Whirlpool CP 08S P6 DK Istruzioni per l'uso Scaricare il pdf (Pagina 21)

Gas supply

• Check that the appliance is set for the type of gas available

and then connect it to the mains gas piping or the gas

cylinder in compliance with the applicable norms in force.

• This appliance is designed and set to work with the gas

indicated on the label situated on the actual hob. If the gas

supply is different from the type for which the appliance

has been set, replace the corresponding nozzles (provided),

following the instructions given in the paragraph "Adaptation

to different types of gas".

• For trouble-free operation, suitable use of energy and a

longer life cycle for the appliance, make sure that the supply

pressure complies with the values indicated in table 1

"Burner and nozzle specifications", otherwise install a

special pressure regulator on the supply pipe in compliance

with current standards and regulations.

• Connect in such a way that the appliance is subjected to

no strain whatsoever.

Either a rigid metal pipe with fittings (fig. 8-D) in compliance

with norms must be used for connecting to the nipple union

(threaded - cylindrical ½"G fitting "F") situated at the rear of

the appliance (fig. 8), or a flexible steel pipe with a continuous

wall and fittings (fig. 8-C) in compliance with norms, which

must not exceed 2000 mm in length. Check that the connecting

pipe cannot come into contact with moving parts which could

damage or crush it. For installation with a flexible rubber pipe,

apply the special hose support for liquid gas (fig. 8-A) or

natural gas (fig. 8-B). The gasket "G" (provided) must be

utilised in every type of connection. The two ends of the pipe

must be fastened with the purpose designed pipe collars "E",

in compliance with the norms. The flexible pipe should comply

with the norms, and be specific for the type of gas used. In

addition:

• it should be as short as possible, with a maximum length of

1.5 metres;

• it should not be bent or kinked;

• it should not be in contact with the rear panel of the appli-

ance or in any case with parts which may reach a tempera-

ture of 50°;

• it should not pass through holes or slits used for discharging

the oven flue gases;

• it should not come into contact with pointed parts or sharp

corners;

• it should be easy to inspect along its entire length in order to

be able to check its condition;

• it should be replaced before the date printed on the actual

pipe.

Important: A pressure regulator, in compliance with the

applicable norm in force, must be inserted when

connecting to a liquid gas supply (in a cylinder).

Upon completion of installation, check for leaks from the

gas circuit using a soapy solution (never use a flame). Make

sure that the natural gas pipe is adequate for a sufficient

supply to the appliance when all the burners are lit.

Adapting to different types of gas (instructions for the hob)

To adapt the hob to a different type of gas from the factory-

set one (indicated on the rating plate at the top of the hood or

on the packaging), the burner nozzles should be replaced as

follows:

• Remove the hob grids and slide the burners off their seats.

• Unscrew the nozzles (fig. 9), using a 7 mm socket spanner

and replace them with nozzles for the new type of gas (see

table 1 "Burner and nozzle characteristics").

Reassemble the parts following the above procedure in the

reverse order.

• On completion of this operation, replace the old rating sticker

with one indicating the new type of gas used.

Adjusting the primary air of the burners

The primary air of the burners does not need to be adjusted.

Adjusting the low flame

• Turn the tap to the low flame position;

• Remove the knob and turn the adjusting screw, situated to

the right of the tap (fig. 10) until you obtain a regular small

flame, using a screwdriver (loosening the screw increases

the height of the flame, tightening decreases it).

N.B.: In the case of liquid gas, the regulation screw must be

screwed in all the way.

• Having obtained the low flame setting required and with the

burner lit, abruptly change the position of the knob several

times from minimum to maximum and vice versa and check

that the flame does not go out.

• In appliances fitted with the safety device (thermocouple),

should the device fail to work with the burners set to the low

flame setting, increase the low flame setting of the same on

the adjusting screw.

Once the adjustment has been made, remount the seals on the

by-passes using sealing wax or similar.

INSTRUCTIONS FOR THE INSTALLER

fig.9

fig.10fig.8

of the electric fan if installed. Liquid petroleum gas descends

towards the floor as it is heavier than air. Apertures in the

outside walls in rooms containing LPG cylinders should

therefore be at floor level, in order to allow any gas from

leaks to be expelled. Do not store LPG cylinders (even when

empty) in basements/rooms below ground level; it is advisable

to keep only the cylinder in use in the room and connected

far from heat sources which could raise its temperature to

above 50°C.

1 2 ... 16 17 18 19 20 21 22 23 24

Commenti su questo manuale

Nessun commento

Whirlpool CP 08S P6 DK Istruzioni per l'uso Pagina 21

Commenti su questo manuale

Prodotti e manuali riguardandi Piani cottura Whirlpool CP 08S P6 DK