Whirlpool L-58 Specifiche

JOB AIDPart No. 4321848CONSUMER SERVICES TECHNICALEDUCATION GROUP PRESENTSL-61Cycles/TempsOnSelectOptionsAutomaticReg/Heavy-HighPerm Press-MedDelicate

6-- NO-- NO-- NO-- NO-- NOTES --TES --TES --TES --TES --

7FILL3. The water level transducer will sense the waterlevel in the basket and send a signal to the micro-computer assembly. The microcomputer suppli

8Figure 7DRAINNOTE: The Start Capacitor and Start Winding of the Drive Motor are energized from P9 during theDrain Cycle.NOTE: The Drain Cycle will

9Figure 9Electronic Gas and Electric DryersAUTOMATIC DRY1. When any of the Automatic options are selected the dryer will run and the LED indicatorabov

10( ( ( ( ( ... ) Section 3 - CONFIRMATION OF ) Section 3 - CONFIRMATION OF ) Section 3 - CONFIRMATION OF ) Section 3 - CONFIRMATION OF ) Section 3

11Section 4SERVICING WASHERS AND DRYERSSERVICING WASHERS AND DRYERSSERVICING WASHERS AND DRYERSSERVICING WASHERS AND DRYERSSERVICING WASHERS AND DRYER

12TESTING AND DIAGNOSISSTARTING TEST MODE1. Press the following “Select” pads in sequence. (Entire sequence must be done within 10seconds) (Fig. 11)T

13Figure 13LID AND SPIN TEST1. Make sure the washer lid is closed before starting test.2. Press “SELECT” pad under Temperature four times to turn off

14d. If the washer still does not spin, leave the washer plugged in and check for 120VAC fromconnectors P14 (W-OR) to P7 (W-BK) during step 1.e. If 12

15d. If the washer still does not spin, leave the washer plugged in and check for 120VAC fromconnectors P8 (BU) to P7 (W-BK) during step 1.e. If 120VA

INTRODUCTIONThis Job Aid, “Washers and Dryers with Fifth Generation Solid State Electronic Controls,” L-61, PartNo. 4321848 provides specific instruc

16b. Open the console and inspect for loose connections. Disconnect and reconnect all wiresfrom the electronic control assembly.c. Close the console,

17d. If the washer still does not agitate, open the console and check for 120VAC from connectorsP14 (W-O) and P7 (W-BK) during step 1.e. If 120VAC is

18 SERVICING PROCEDURESSOLID STATE ELECTRONIC CONTROLSNOTE: All diagnostic tests must be performed before any attempt is made to remove the electroni

19AutomaticCycles/TempsOnSelectReg/Heavy-HighPerm Press-MedDelicate-LowFluff Air-No HeatTumble Press-MedDamp Dry-HighVery DryMore Dry*Reg DryLess DryL

20TESTING AND DIAGNOSISDiagnosticsThe following problems can be diagnosed by observing the indicator LEDs on the control panel.Power FailureWhen the 3

21a. If the motor does not start and there is an “Invalid Tone”, check the door switch. (D to D1)b. If the motor does not start and the Drying LED lig

222. Select Automatic - Less Dry and press “START”.3. If the motor will not stop after 16 seconds, check sensor strip (Y-R to G-Y).a.If 0 ohms with no

23Thermal Cut-OffFifth generation electronic electic dryers are equipped with a “one-shot” thermal cut-off. If the dryerdoes not heat and there are 2

24( ( ( ( ( ... ) Section 4 - CONFIRMATION OF ) Section 4 - CONFIRMATION OF ) Section 4 - CONFIRMATION OF ) Section 4 - CONFIRMATION OF ) Section 4

25Section 5TECH TIPSTECH TIPSTECH TIPSTECH TIPSTECH TIPSTESTING PROCEDURE FOR WATER LEVEL TRANSDUCERWashers equipped with 5th Generatiuon Electronic C

TABLE OF CONTENTSINTRODUCTION IIITABLE OF CONTENTS IVSECTION 1 - EQUIPMENT AND SAFETY 1SECTION 2 - INSTALLATION CONSIDERATIONS 3SECTION 3 - THEORY OF

26WIRING DIAGRAMSWIRING DIAGRAMSWIRING DIAGRAMSWIRING DIAGRAMSWIRING DIAGRAMSTHREE SPEED AUTOMATIC WASHER

27CONFIRMATION OF UNDERSTANDING EXERCISESCONFIRMATION OF UNDERSTANDING EXERCISESCONFIRMATION OF UNDERSTANDING EXERCISESCONFIRMATION OF UNDERSTANDING E

28

-- NOTES --

1Section 1EQUIPMENT AND SAFETYEQUIPMENT AND SAFETYEQUIPMENT AND SAFETYEQUIPMENT AND SAFETYEQUIPMENT AND SAFETYEQUIPMENTAll tests/checks should be made

2-- NO-- NO-- NO-- NO-- NOTES --TES --TES --TES --TES --

3Section 2INSTALLATION CONSIDERATIONSThe most common cause of electronic control failure are the result of issues related to proper instal-lation. Be

4INLET HOSESThe rubber washers and inlet hoses on washers with 5th Generation Electronic Controls have beeninstalled in the factory. They will be fou

5Section 2Section 2Section 2Section 2Section 2( ( ( ( ( ... ) ) ) ) ) CONFIRMATION OF UNDERSTANDINGCONFIRMATION OF UNDERSTANDINGCONFIRMATION OF